TP-LINK TL-SL2210 Installation Guide

Installation GuideSmart SwitchTL-SL2210/TL-SL2218/TL-SL2428/TL-SL2452Enterprise Networking Solution

05Smart SwitchMake sure that the package contains the following items. If any of the listed items is damag

06Smart SwitchSite Requirements To ensure normal operation and long service life of the device, please install it in an environment that meet

07Smart SwitchKeep the device far from high-frequency, strong-current devices, such as radio transmitting station.Use electromagnetic shiel

08Smart SwitchESD-preventive wrist wrap Cables Note: These tools are not provided with our product. If needed, please self purchasethem.

09Smart SwitchBracket InstallationFigure 2-2 After the brackets are attached to the device, use suitable screws (not provided) to 3. secure the bracke

10Smart SwitchIn the actual network environment, you may need cable outdoors and indoors, a

11Smart SwitchRequirements for Cabling Indoors When cabling indoors, keep a certain distance away from the devices that may cause high-frequency int

12Smart Switch2~5kVA powerlineParallel cabling 300One is in the grounded metal raceway or metal pipe 150The both are in the grounded metal raceway or

13Smart SwitchNote: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them.Connecting to the G

14Smart SwitchGrounding T e rminal Equipotential Bonding CableGrounding Bar Ground CableEquipotential BondingFigure 3-3 When equipotential bonding,

ISpecifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Othe

15Smart SwitchThe port rate of the signal lightning arrester should match the rate of the desired port on the device. If it is not matched, t

16Smart SwitchPlease connect the Ethernet ports of the switch to the network devices by RJ45 cable as the followi

17Smart SwitchAfter completing the installation, please verify the following items:There are 5~10cm of clearance around the

18Smart SwitchTo access the GUI of the switch, open a web browser and type the default 1. management address http://19

19Smart Switch         With the switch powered on,

20Smart SwitchItem ContentStandards and Protocol IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX/100Base-FXIEEE 802.3ab

21Smart SwitchFor more help, please go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver

22Smart SwitchRussian Federation Tel: 8 (499) 754 5560 (Moscow NO.) 8 (800) 250 5560 (Toll-free within RF)E-mail: [email protected] t

Website: http://www.tp-link.com E-mail: [email protected] 7106504458 REV1.3.0

IIThe User Guide is provided on the resource CD. To obtain the latest product information, please visit the official Web

IIIThis Installation Guide is for:Network EngineerNetwork AdministratorDue to the similarity in structure of TL-SL2210/TL-SL2

IVContentsChapter 1 Introduction —————————————— 011.1 Product Overview ... 011.2 Appearance ...

01Smart SwitchTL-SL2210/TL-SL2218/TL-SL2428/TL-SL2452 is compliant with the IEEE802.3 Ethernet protocols.T

02Smart SwitchFront Panel of TL-SL2428Figure 1-3 The front panel of TL-SL2452 is shown as Figure 1-4. RESETLEDs10/100Mbps RJ45 Port10/100/1000Mbps

03Smart SwitchPort Feature Model 10/100Mbps RJ45 Port 10/100/1000Mbps RJ45 Port SFP PortTL-SL2210 8 1 1TL-SL2218 16 2 2(Combo)TL-SL2428 24 4 2(Combo)T

04Smart SwitchThe rear panel of TL-SL2218 is shown as Figure 1-6. Grounding Terminal Power SocketRear Panel of Figure 1-6 TL-SL2218The rea