Installation Guide L2 Managed SwitchTL-SL5428EBusiness Networking Solution
05 L2 Managed SwitchPlease keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity
06 L2 Managed Switchinstant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. Ensur
07 L2 Managed SwitchTurnover the device and attach the supplied rubber feet to the recessed areas on 3. the bottom at each corner of the device.
08 L2 Managed SwitchIn the actual network environment, you may need cable outdoors and indo
09 L2 Managed SwitchRequirements for the distance between Ethernet cable and other pipelines are shown in the table.Other PipelinesEthernet CableMin
10 L2 Managed SwitchConnecting the device to ground is to quickly release the lightning over-voltage and over-current of th
11 L2 Managed SwitchNote:The figure is to illustrate the application and principle. The power cord you get from the package and the socket in your
12 L2 Managed SwitchPower lightning arrester and signal lightning arrester are used for lighting protection.Power lightning
13 L2 Managed SwitchConnectionConnect the Ethernet ports of the switch to the network devices by RJ45 cable as t
14 L2 Managed SwitchConnectionConnecting the Console PortFigure 4-3 You can also manage the device through the console port, for details please refer
ISpecifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other
15 L2 Managed SwitchNote: The gure is to illustrate the application and principle. The power cord you get from the package and the socket in your
16 L2 Managed SwitchNote: To log on to the GUI of the switch, the IP address of your PC should b
17 L2 Managed SwitchMain Page of the SwitchFigure 5-3 You can log on to the switch and access the CLI by the followi
18 L2 Managed SwitchThe Connection Description Window will prompt as Figure 5-5. Enter a name into the 3. Name field and click OK.Connection Descripti
19 L2 Managed SwitchPort SettingsFigure 5-7 The DOS prompt ”TL-SL5428E>” will appear after pressing the Enter button as 6. shown in Fig
20 L2 Managed SwitchOpen the Run windowFigure 5-9 Type in cmd in the prompt Run window as Figure 5-10 and click OK.4. Run WindowFigure 5-10 Type in
21 L2 Managed SwitchType in the User name and Password (the factory default value for both of them is 6. admin) and press the Enter button, then you c
22 L2 Managed SwitchConnect the console port of the
23 L2 Managed SwitchItem ContentStandardsIEEE 802.3 10Base-T EthernetIEEE 802.3u 100Base-TX/100Base-FXIEEE 802.3ab 1
24 L2 Managed SwitchFor more help, please go to: http://www.tp-link.com/en/support/faq To download the latest Firmware,
IIRelated DocumentThe User Guide and CLI Reference Guide of the product are provided on the resource CD.To obtain the latest product
25 L2 Managed SwitchPoland Tel: +48 (0) 801 080 618 +48 223 606 363 (if calls from mobile phone) Fee: Depending on rate of different carriers.E-mail:
Website: http://www.tp-link.com Tel: +86 755 26504400 E-mail: [email protected]
IIIThis Installation Guide is for:Network EngineerNetwork AdministratorThis guide uses the specific formats to highlight specia
IVContentsChapter 1 Introduction ———————————— 011.1 Product Overview ...011.2 Appearance ...
01 L2 Managed Switch TP-LINK JetStream L2 Managed Switch, designed for workgroups and departments,
02 L2 Managed SwitchNote: The port 25–28 of the switch are “Combo” ports. A “Combo” port consists of a RJ45 port and an SFP port, and the two ports sh
03 L2 Managed SwitchPower SocketConnect the female connector of the power cord here, and the male connector to the AC power outlet. Please make
04 L2 Managed SwitchMake sure that the package contains the following items. If any of the listed item
Comments to this Manuals