TP-LINK TL-SL3428 User Manual

Installation Guide L2 Managed SwitchTL-SL3428/TL-SL3452Enterprise Networking Solution

05 L2 Managed SwitchPlease keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity

06 L2 Managed Switchprotection measures should be taken. Ensure the rack and device are well earthed. Make sure the power socket has a good contact

07 L2 Managed SwitchTurnover the device and attach the supplied rubber feet to the recessed areas on 3. the bottom at each corner of the device.

08 L2 Managed SwitchIn the actual network environment, you may need cable outdoors and indo

09 L2 Managed SwitchRequirements for the distance between Ethernet cable and other pipelines are shown in the table.Other PipelinesEthernet CableMin

10 L2 Managed SwitchConnecting the device to ground is to quickly release the lightning over-voltage and over-current of th

11 L2 Managed SwitchNote:The figure is to illustrate the application and principle. The power cord you get from the package and the socket in your

12 L2 Managed SwitchPower lightning arrester and signal lightning arrester are used for lighting protection.Power lightning

13 L2 Managed SwitchConnectionConnect the Ethernet ports of the Switch to the network devices by RJ45 cable as t

14 L2 Managed SwitchConnectionCLI (Command Line Interface) enables you to manage the Switch, thus you can load the CLI after conne

ISpecifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other

15 L2 Managed SwitchConnecting to Power SupplyFigure 4-4 Note: The gure is to illustrate the application and principle. The power cord you get from

16 L2 Managed SwitchTo access the GUI of the Switch, open a web browser and type th

17 L2 Managed SwitchMain Page of the SwitchFigure 5-3 You can log on to the Switch and access the CLI by the followi

18 L2 Managed SwitchThe Connection Description Window will prompt as Figure 5-5. Enter a name into the 3. Name field and click OK.Connection Descripti

19 L2 Managed SwitchPort SettingsFigure 5-7 Type the User name and Password in the Hyper Terminal window, the factory default 6. value for both of

20 L2 Managed SwitchOpen the Run windowFigure 5-9 Type cmd in the prompt Run window as Figure 5-10 and click OK.3. Run WindowFigure 5-10 Type telnet

21 L2 Managed SwitchType the User name and Password (the factory default value for both of them is 5. admin) and press the Enter button, then yo

22 L2 Managed SwitchConnect the console port of th

23 L2 Managed SwitchItem ContentStandardsIEEE 802.3 10Base-T EthernetIEEE 802.3u 100Base-TX/100Base-FXIEEE 802.3ab 1

24 L2 Managed SwitchFor more help, please go to: http://www.tp-link.com/en/support/faq To download the latest Firmware,

IIRelated DocumentThe User Guide and CLI Reference Guide of the product are provided on the resource CD.To obtain the latest product

25 L2 Managed SwitchRussian Federation Tel: 8 (499) 754-55-60 8 (800) 250-55-60 (toll-free call from any RF region)E-mail: [email protected]

Website: http://www.tp-link.com Tel: +86 755 26504400 E-mail: [email protected]

IIIThis Installation Guide is for:Network EngineerNetwork AdministratorDue to the similarity in structure of the L2 managed Swi

IVContentsChapter 1 Introduction ———————————— 011.1 Product Overview ...011.2 Appearance ...

01 L2 Managed Switch TP-LINK JetStreamTM L2 Managed Switch, designed for workgroups and departments, provi

02 L2 Managed SwitchLEDsLED Status IndicationPWROn The Switch is powered onOff The Switch is powered off or power supply is abnormalFlashing Power sup

03 L2 Managed SwitchNote: For TL-SL3428, when using the SFP port with a 100Mbps module or a gigabit module, you need log on to the GUI (Graphical Us

04 L2 Managed SwitchMake sure that the package contains the following items. If any of the listed item